AstroBin

AstroBin

AstroBin

ASIAIR mini not guiding EQ6 pro ZWO ASIAIR Mini · Bostjan · ... · 4 · 172 · 0

BopsBops 0.00
Bostjan
...
· 
·  1 like
·  Share link
Hello,

I have a problem with asiair mini not guiding.

I setup everything, connect asiair and mount with usb cable. I do polar alignment with asiair and it goes. The mount is tracking and goto is working perfectly. But when I start guiding with asiair over ZWO 120mm it popups that the mount is far from the celestial equator. For accurate result, please calibrate at declination of -30 to +30 degrees. It starts callibrating and doesnt stop. So guiding is not working with asiair but the mount itself guides ok.

I done the same with skywatcher star adventurer and it worked. With EQ6pro i set EQMod option and baud 115200. Everything works except the callibration.

Thank you!
Like
×

Sorry :-(

Editing a post is only allowed within 24 hours after creating it.
×

Share this forum post

Copy the URL below to share a direct link to this post.

Close
×

Post editing not available

This post cannot be edited using the classic forums editor.

To edit this post, please enable the "New forums experience" in your settings.

Go to Settings Close
GoldTop57 0.90
GoldTop57
...
· 
·  1 like
·  Share link
Hi you'll need to calibrate closer to the celestial equator: https://www.youtube.com/watch?v=HXRbFBeKf84&t=1206s 11:48.

Good luck!
Like
×

Sorry :-(

Editing a post is only allowed within 24 hours after creating it.
×

Share this forum post

Copy the URL below to share a direct link to this post.

Close
×

Post editing not available

This post cannot be edited using the classic forums editor.

To edit this post, please enable the "New forums experience" in your settings.

Go to Settings Close
BopsBops 0.00
Bostjan
Topic starter
...
· 
·  Share link
Yes i saw that. So basicly i do the PA than I set goto to the target away from the meridian and close to the equator as stated between 0 and 30 degrees. Than start the guiding and callibration should be done? After that I can moove to the shooting target. Thanks
Like
×

Sorry :-(

Editing a post is only allowed within 24 hours after creating it.
×

Share this forum post

Copy the URL below to share a direct link to this post.

Close
×

Post editing not available

This post cannot be edited using the classic forums editor.

To edit this post, please enable the "New forums experience" in your settings.

Go to Settings Close
GoldTop57 0.90
GoldTop57
...
· 
·  Share link
Yes thats correct, perform the PA, move to a spot close to the Celestial Equator and start guiding. Once calibration is complete you can move to your target.
Like
×

Sorry :-(

Editing a post is only allowed within 24 hours after creating it.
×

Share this forum post

Copy the URL below to share a direct link to this post.

Close
×

Post editing not available

This post cannot be edited using the classic forums editor.

To edit this post, please enable the "New forums experience" in your settings.

Go to Settings Close
Apostrophe 0.00
Martin Lück
...
· 
·  1 like
·  Share link
Yes, I know the problem too. But when I then return to the original destination, the ASI Air first recalibrates the guiding at the start of the recording.
Although the destination is then far away from the equator again.
Like
×

Sorry :-(

Editing a post is only allowed within 24 hours after creating it.
×

Share this forum post

Copy the URL below to share a direct link to this post.

Close
×

Post editing not available

This post cannot be edited using the classic forums editor.

To edit this post, please enable the "New forums experience" in your settings.

Go to Settings Close
 
Register or login to create to post a reply.
×

Warning!

This operation will reload the current page. If you have any unsaved information in a form, it will be lost.

You can also dismiss this window, and your operation will be applied at the next page navigation.