
I designed the rings and the EAF holder myself, but the Adapter for GT2 belts can be found here:
https://www.thingiverse.com/thing:4761672/files
It is a tight fit but can easily be made a little wider with some sanding paper
Have fun,
Michael
![]() ...
·
![]()
·
2
likes
|
---|
In order to use the ZWO EAF with the Samyang 135mm you need a focusser ring to adapt to GT2 belts. ![]() I designed the rings and the EAF holder myself, but the Adapter for GT2 belts can be found here: https://www.thingiverse.com/thing:4761672/files It is a tight fit but can easily be made a little wider with some sanding paper Have fun, Michael |
![]() ...
·
![]()
·
4
likes
|
---|
![]() Here's the design for the Adapter rings: https://a360.co/42DEtjU and the STLs for the bigger (80mm) and the smaller (70mm) ring 80mm top.stl80mm bottom.stl70mm top.stl70mm bottom.stl and the dovetail: https://a360.co/43zqGMv Dovetail v1.stl Print the Dovetail standing on it's small side, this will make the print more stable for claming things into the dovetail. The knobs for tightening the rings were taken from this model: https://www.printables.com/model/466697-samyangrokinon-135mm-rings-fine-bahtinov-mask/files |
![]() ...
·
![]() |
---|
Hi Michael! Nice setup! I noticed in the photo that you are using the ZWO adapter. I recently purchased the Astro Essentials M48 adapter and was wondering when you started using it. Have you noticed any improvements in star quality in the corners of your images? CS |
![]() ...
·
![]() |
---|
Michael Ring: I'm currently building my own dual Nikon Samyang rig using IMX571 sensors. I have one mono with a 2" EFW and have yet to decide whether I go for another one or the OSC version. Do you have any more images of your setup? I'm still trying to figure out how I can best manage to assemble it all but your solution looks solid. Are you getting the exact same FOV? |
![]() ...
·
![]() |
---|
I will create some extra pics tomorrow. Getting the two cameras to point at the same place is quite easy, you can first capture one picture each when the two lenses are parallel (in the distance from each other as you need them to be), then you simply plate solve and look at the center coordinates of the two images and split the difference of the angle between the DEC part of the center coordinates. Then you can 3d print a triangle with exactly that angle. You may also manually adjust the aluminium frame until a star is centered in the FOV of both cameras but the 3d printed angle feels a little more precise. My goal with the design was to get two fields at the same time, this is the reason why the two lenses form a V, to have them point to the same field I'd have to mount them in the other direction and the angle would have to be smaller. |
![]() ...
·
![]() |
---|
Much appreciated!
|
![]() ...
·
![]() |
---|
![]() ...
·
![]() |
---|
Michael Ring: Hi Michael, thank you for uploading this, this is exactly what I need. I also have a general question about using the EAF with the Samyang: On my standard telescope the Asiair is moving the focus back and forth while running an autofocus procedure. Since the Samyang has its infinity position more or less at the end of its travel range, how does it work with the EAF? I image that there is the risk that the focusser bumps the focus ring into its mechanical limit. I am wondering if autofocus is still possible this way or if I should stick with a manual focus procedure. What is your experiance with that? |
![]() ...
·
![]() |
---|
AF works just fine, you only need to make sure that your backfocus is tuned well, then you have enough space from infinity to the hard end stop. Lso make sure that the overshoot is set so that the focused moves from infinity in direction of shorter distance. When you configure it in the wrong way the overshoot movement will hit the end stop. Michael |
![]() ...
·
![]() |
---|
Thank you, that is very helpful and I will keep it in mind.
|